ArticlesArticles Most Popular ArticlesMost Popular Articles Most Helpful ArticlesMost Helpful Articles Submit A QuestionSubmit A Question Login for PRIORITY RESPONSELogin for PRIORITY RESPONSE
RSS Feeds
DrillDown Icon Table of Contents
DrillDown Icon LIABILITY & COPYRIGHT
DrillDown Icon Site Information
DrillDown Icon * Support
DrillDown Icon Technical Info - Adhesives
DrillDown Icon Technical Info - Master Airscrew
DrillDown Icon Technical Info - POLYPRO
DrillDown Icon Technical Info - RC Flying - General
DrillDown Icon Technical Info - RC Flying Electric - General
DrillDown Icon Technical Info - ULTRA POWER Technology - Products
DrillDown Icon Technical Info - VMAR - General
DrillDown Icon VMAR - Documents
DrillDown Icon VMAR - Adhesives
DrillDown Icon VMAR - Canopy (Window) Cleaning
DrillDown Icon VMAR - Canopy (Window) Replacement
DrillDown Icon VMAR - CG Location - General
DrillDown Icon VMAR - Cleaning Model Aircraft
DrillDown Icon VMAR - Construction
DrillDown Icon VMAR - Control Surfaces
DrillDown Icon VMAR - Covering
DrillDown Icon VMAR - Cowl Installation
DrillDown Icon VMAR - Electric Power Conversions
DrillDown Icon VMAR - Engine Mounting
DrillDown Icon VMAR - Engine Power Module
DrillDown Icon VMAR - Flaps & Flaperons
DrillDown Icon VMAR - Fuel Leaks - Fuselage Soaked - What now?
DrillDown Icon VMAR - Fuel Proofing
DrillDown Icon VMAR - Fuel Tanks
DrillDown Icon VMAR - Glow Power Conversions
DrillDown Icon VMAR - Hardware & Fittings
DrillDown Icon VMAR - Jet (Turbine) Power Conversions
DrillDown Icon VMAR - Landing Gear
DrillDown Icon VMAR - Packaging
DrillDown Icon VMAR - Parts
DrillDown Icon VMAR - Servo Trays
DrillDown Icon VMAR - Specifications of Models
DrillDown Icon VMAR - Wings
DrillDown Icon Wing - Ailerons Loose on Torque Rods - How to Tighten
DrillDown Icon Wing - Aileron Torque Rod angle different between wing halves - How do I fix?
DrillDown Icon Wing Alignment Dowels - Tight Fit
DrillDown Icon Wing Bolts Broken
DrillDown Icon Wing Bolts - Will not Thread.
DrillDown Icon Wing - Dihedral
DrillDown Icon Wing - Gaskets and Fairings
DrillDown Icon Wing Joints - Do it Right.
DrillDown Icon Wing Joint Tape - How to Use?
DrillDown Icon Wing Saddle Fit
DrillDown Icon Wing Spar Joiner - Fit
DrillDown Icon Wing Tubes - Loose Fit
DrillDown Icon Wing Tubes - Glue or Not?
DrillDown Icon Wings - Wing Tips Hang Down (droop)
DrillDown Icon VMAR - Wing Fairing Replacement
DrillDown Icon VMAR - Wood Types Used
DrillDown Icon Technical Info - VMAR - Products
DrillDown Icon Technical Info - VMAX Electric Power Systems - General
DrillDown Icon Technical Info - VMAX Electric Power Systems - Products
DrillDown Icon Technical Info - VMAX Engines (Glow) - General
DrillDown Icon Technical Info - VMAX Engines (Glow) - Products
  Email This ArticlePrint PreviewPrint Current Article/Category and All Sub-Articles/Categories
 
Wing - Dihedral - What is It? Is it Adjustable?

Question: What is Wing Dihedral? Is it Adjustable on a VMAR ARF aircraft?

Answer: Dihedral is the bend upwards at the center of the wing. When you look at a wing with dihedral when it is top side up, the wing tips will be higher than the center. The more dihedral the higher the tips. Dihedral provides stability so trainers usually have more than sport airplanes and pattern or aerobatic airplanes often have none at all.

The dihedral on VMAR models is set at the factory. There is nothing to adjust. The angle of the wing roots and the angle of the wing spar joiner ensure that when the wing is assembled properly using 30 minute epoxy, the wing roots will be flush to each other and the correct amount of dihedral will be built into the wing.

Article ID: 4529