ArticlesArticles Most Popular ArticlesMost Popular Articles Most Helpful ArticlesMost Helpful Articles Submit A QuestionSubmit A Question Login for PRIORITY RESPONSELogin for PRIORITY RESPONSE
RSS Feeds
DrillDown Icon Table of Contents
DrillDown Icon LIABILITY & COPYRIGHT
DrillDown Icon Site Information
DrillDown Icon * Support
DrillDown Icon Technical Info - Adhesives
DrillDown Icon Technical Info - Master Airscrew
DrillDown Icon Technical Info - POLYPRO
DrillDown Icon Technical Info - RC Flying - General
DrillDown Icon Technical Info - RC Flying Electric - General
DrillDown Icon Technical Info - ULTRA POWER Technology - Products
DrillDown Icon Technical Info - VMAR - General
DrillDown Icon VMAR - Documents
DrillDown Icon VMAR - Adhesives
DrillDown Icon VMAR - Canopy (Window) Cleaning
DrillDown Icon VMAR - Canopy (Window) Replacement
DrillDown Icon VMAR - CG Location - General
DrillDown Icon VMAR - Cleaning Model Aircraft
DrillDown Icon VMAR - Construction
DrillDown Icon VMAR - Control Surfaces
DrillDown Icon VMAR - Covering
DrillDown Icon VMAR - Cowl Installation
DrillDown Icon VMAR - Electric Power Conversions
DrillDown Icon VMAR - Engine Mounting
DrillDown Icon Installing Engines on the Engine Mounts
DrillDown Icon Engine Orientation and Position
DrillDown Icon Engine Mounts - Plastic vs Aluminum
DrillDown Icon Engine Mounts - Slight Variations in Finish
DrillDown Icon Engine Mounts - Without Clamps
DrillDown Icon Engine Width - What fits and what does not?
DrillDown Icon Firewall - Finished Appearance & Sealing
DrillDown Icon Firewall - Thrust Lines - Can they be moved?
DrillDown Icon Firewall - Thrust Lines - Where are they?
DrillDown Icon Firewall - What is it?
DrillDown Icon Using 4 Stroke Engines
DrillDown Icon VMAR - Engine Power Module
DrillDown Icon VMAR - Flaps & Flaperons
DrillDown Icon VMAR - Fuel Leaks - Fuselage Soaked - What now?
DrillDown Icon VMAR - Fuel Proofing
DrillDown Icon VMAR - Fuel Tanks
DrillDown Icon VMAR - Glow Power Conversions
DrillDown Icon VMAR - Hardware & Fittings
DrillDown Icon VMAR - Jet (Turbine) Power Conversions
DrillDown Icon VMAR - Landing Gear
DrillDown Icon VMAR - Packaging
DrillDown Icon VMAR - Parts
DrillDown Icon VMAR - Servo Trays
DrillDown Icon VMAR - Specifications of Models
DrillDown Icon VMAR - Wings
DrillDown Icon VMAR - Wing Fairing Replacement
DrillDown Icon VMAR - Wood Types Used
DrillDown Icon Technical Info - VMAR - Products
DrillDown Icon Technical Info - VMAX Electric Power Systems - General
DrillDown Icon Technical Info - VMAX Electric Power Systems - Products
DrillDown Icon Technical Info - VMAX Engines (Glow) - General
DrillDown Icon Technical Info - VMAX Engines (Glow) - Products
  Email This ArticlePrint PreviewPrint Current Article/Category and All Sub-Articles/Categories
 
Engine Orientation - Upright, Sideways, Inverted - Relation to Position on FIrewall

Question: How do I position my engine on the engine mounts and on the firewall when I intend on installing the engine at an angle or inverted rather than upright?

Short Answer: Regardless of orientation, the center line of the crankshaft must be positioned over the intersection of the vertical and horizontal thrust lines for your particular model. There are a few exceptions as described below.

Better Answer: Some models pretty much force you to install your engine in an upright orientation. Other models, particularly once you move up from basic trainers, offer you a variety of engine orientation options. Rotated 90 degrees is one such choice that often works well with Pitts style mufflers...  inverted (sometimes called 180 degree rotation) is another choice. Generally these non-upright orientations, hide more of the engine and muffler and result in a more realistic scale like appearance to the model.

The choice of what angle to use is pretty much up to you, limited by the physical size of the engine, muffler, cowl etc. Some engines for example can be oriented at 90 or 135 degrees but run into a physical problem at other angles... they hit something, the muffler won't clear the fuselage, the needle valve is at an awkward location etc. When selecting an angle to mount your engine, you have to balance off appearance, convenience, practicality and most of all make sure it can physically fit. Don't forget to test your planned installation angle with the muffler and carb installed. Also check out your engine manual for any specific guidance from the engine manufacturer. Some manufacturers don't recommend an exactly inverted 180 degree installation. We have found this to be good advice in many cases... 180 degree inversions have a tendency to smother the glow plug in oil and residue if run at low RPM for too long.

Once you've decided on the installation orientation that you want, the actual position of the engine on the firewall is no different with a rotated engine than it is with an upright engine. The engine thrust is always centered around the crankshaft and regardless of orientation, the center line of the crankshaft must be positioned over the intersection of the vertical and horizontal thrust lines for your particular model. The vertical thrust line lies up and down through the middle of the firewall. The horizontal thrust line is often drawn on the firewall or is to be draw on the firewall by you after referencing location information in the model instruction manual.  

There are some exceptions but the exceptions are few and far between... if the mounting face of the engine mounting lugs is offset from the center line of the crankshaft you have to adjust accordingly. This is rare, we have not seen this in standard two stroke engines. Engine manufacturers avoid this if at all possible. If you are working with a large gas engine adapted from another industry or a multi piston engine, examine the mounting system carefully and make sure you understand the relation between the engine mounting lugs and the center line of the crankshaft.

 

Related Articles

Article ID: 2663