ArticlesArticles Most Popular ArticlesMost Popular Articles Most Helpful ArticlesMost Helpful Articles Submit A QuestionSubmit A Question Login for PRIORITY RESPONSELogin for PRIORITY RESPONSE
RSS Feeds
DrillDown Icon Table of Contents
DrillDown Icon LIABILITY & COPYRIGHT
DrillDown Icon Site Information
DrillDown Icon * Support
DrillDown Icon Technical Info - Adhesives
DrillDown Icon Technical Info - Master Airscrew
DrillDown Icon Technical Info - POLYPRO
DrillDown Icon Technical Info - RC Flying - General
DrillDown Icon Technical Info - RC Flying Electric - General
DrillDown Icon Technical Info - ULTRA POWER Technology - Products
DrillDown Icon Technical Info - VMAR - General
DrillDown Icon Technical Info - VMAR - Products
DrillDown Icon Technical Info - VMAX Electric Power Systems - General
DrillDown Icon Technical Info - VMAX Electric Power Systems - Products
DrillDown Icon Technical Info - VMAX Engines (Glow) - General
DrillDown Icon VMAX Engines - Documents
DrillDown Icon Engine Bearings - Replace or Not?
DrillDown Icon Engine Piston & Sleeve - Replace or Not?
DrillDown Icon After Run Oil - Why use it?
DrillDown Icon Engine Carburetor - Spray Bar - Alignment
DrillDown Icon Engine Carburetor - Rotor Difficult to Rotate
DrillDown Icon Engine Carburetor - Low Speed Mixture - How to Set?
DrillDown Icon Engine Carburetor - Will not shut off.
DrillDown Icon Engine Cleaning - How to Do It?
DrillDown Icon Engine Dimensions (Sizes)
DrillDown Icon Engine Head Bolts - How Tight?
DrillDown Icon Engine - Inverted Operations
DrillDown Icon Engine OK on Ground - Poor in Flight
DrillDown Icon Engine Power - What is Appropriate?
DrillDown Icon Engine Prop Size?
DrillDown Icon Engine (ABC type) - Clyinder (Sleeve) Removal
DrillDown Icon Engine (ABC type) - Crankshaft Removal
DrillDown Icon Engine (ABC type) - Piston Removal
DrillDown Icon Engine (ABC type) is Tight at Top Dead Center - Is something wrong?
DrillDown Icon Engine Storage - Preparation
DrillDown Icon Engine Types and Power Considerations
DrillDown Icon Rust - How to Remove It?
DrillDown Icon Rust - Why is it Bad? How to Prevent It?
DrillDown Icon Technical Info - VMAX Engines (Glow) - Products
  Email This ArticlePrint PreviewPrint Current Article/Category and All Sub-Articles/Categories
 
Engine (ABC type) is Tight at Top Dead Center - Is something wrong? What should I do?

Question: My VMAX 46 or 52 or other VMAX ABC type engine is very tight at top dead center particularly just out of the box. It is so tight that I hear a clicking noise at the top of the piston travel and it is very difficult to turn it over by hand. Is something wrong? What should I do?

Answer: No nothing is wrong. Please review your instruction manual and in particular the BREAK IN section.

Better Answer: ABC engines have a tapered sleeve which creates a tight fit around the piston at top dead center. The tightness is quite pronounced when the engine is new and cold. As the engine warms up, the sleeve expands and the fit is not quite so tight. The top of the sleeve gets much warmer than the bottom and hence it has been made narrower to allow for more expansion while retaining compression.

Your instruction manual contains specific information related to your engine. The BREAK IN section is very important. The VMAX 46 and 52 engine manual has a note that is boxed to draw attention to it. This note is located on page 3 of the manual in the top left corner and deals specifically with the question of tight fit at top dead center. The note reads as follows:

THIS IS AN ABC ENGINE. IT WILL BE VERY TIGHT AT TOP DEAD CENTER. THIS IS NORMAL. AFTER THE FIRST FEW RUNS IT WILL LOOSEN UP SOMEWHAT BUT REMAIN TIGHTER AT THE TOP WHEN COLD THROUGH ITS LIFE.

We cannot overstate the importance of reading the entire manual before attempting to operate your engine.

 

 

Article ID: 2685