Stage 2 - Power Module Wiring - For VMA-T210X Twin Otter
 
a) Review the Read Me First documentation and the Assembly and Operations Manual that came with your model. Continue with the assembly procedures provided therein.
 
b) When you are ready to begin Stage 9 of the Assembly and Operations Manual pause and review Stage 9 and these notes carefully.
 
c) Stage 9 of the Assembly and Operations Manual covers the installation of the electric motors and speed controls. In effect by purchasing a VMAX Power Module you have avoided much of this work. Consult the illustrations 9A through 9F for reference purposes but you can skip the work itself.
 
d) You will need to do the wiring.
  • If you have purchased the VMAR Wiring Harness Set for this model (VMA-T210XWHS) please see the detailed wiring instructions provided therein.
  • If you do NOT have the VMAR Wiring Harness Set for this model you will need to use your own wiring setup. Make sure whatever you do is compatible with your radio system, your servos, your battery and the speed controls.
    • Note: Modelers who are not experienced with multi-motor electric flight systems are strongly encouraged to use the VMAR Wiring Harness Set applicable to their VMAR multi-motor model. Scratch building and installing a reliable wiring harness set for a multi-motor electric model requires approximately 8 hours of work & considerable knowledge and experience.    
  • Figure 9M of the Assembly and Operations Manual shows a generic wiring schematic that may be helpful. Be particularly careful with the thin red wires coming from the Electronic Speed Controls (ESC).  Figure 9M shows these joined together between the ESC's while only the Negative (-) and Signal  wires run to the throttle channel of the receiver. This may or MAY not be suitable for your receiver. You will need to nail this down before connecting anything. The most common setup today is to NOT hook the red wires from the ESC to themselves or anything else. Just work with the Negative (-) and Signal wires from the ESC's all the way to the throttle channel on your receiver.
  • To add some complexity to the ESC wiring, there is no standard color schema used by all radio manufacturers. Caution is a must. To help you design and connect your wiring please see the generic wiring information provided in the Read Me First information that came with your model and reprinted below for your convenience. This should be considered a guideline only.
    • Note: There are some risks here and if you are not electronically inclined you should get help and consider purchasing the VMAR Wiring Harness Set for this model.  
 
 
VMA-T210X Twin Otter 09-15 ARF - Electric Power - Wiring
Question: My VMAR VMA-T210X Twin Otter 09-15 ARF uses two motors. How should I wire these up so that I can control them from the single throttle channel on my receiver?
 
Answer: The simplest solution is to use our VMAX Power Pack which comes with brushless motors, electronic speed controls (ESC), battery pack, propellors etc and includes a custom made Wiring Harness Set for the Twin Otter power and control system. The Power Pack for the Twin Otter is #VMM-T210XPP1.
 
If you have your own motors, servos, speed controls etc that you intend on using in the VMAR Twin Otter the manufacturer of these electric components is your best bet for advice on operating in a Twin Power configuration. The Wiring Harness Set for the Twin Otter (#VMA-T210XWHS) is available as an aftermarket accessory and in most installations will make it much easier to work with the VMAX Power Module, third party motors, speed controls and servos.
 
If you have purchased the VMAX Power Pack for the Twin Otter (#VMM-T210XPP1) please follow the installation instructions that come with the Power Pack. The VMAX Power Pack will save you hours and hours of time and greatly reduce the chances of making an expensive mistake.
 
If you are using third party power components, follow their instructions. In the absence of specific information from the manufacturer here are some general tips that may assist you. Remember, without specific information from the supplier of your Motors and ESC, you run the risk of doing something wrong and such booboos are usually expensive. Use our tips with this in mind. We can't verify that these tips will work with third party equipment and strongly encourage you to obtain information from the manufacturer of your Motors and ESC.
 
a) Use two idential Brushless Motors and two identical Electronic Speed Controls (ESC). Each motor should have its own speed control. (see footnote below)
 
b) Connect each ESC to a Brushless Motor using the color coded wire as a guide. Test and ensure that the motor turns in the direction expected and that thrust is aft of the motor.
 
c) Make a power Y-connector to feed power from your LiPo battery to the power input leads on both of your ESC's. 
 
d) Use the power Y-connector to connect the power input to the ESC's to a common (1) LiPO battery source.
 
e) Make a throttle Y-connector. This is necessary for DUAL ESC operation which assumes that you are using two motors and two ESC's.
 
For DUAL ESC operation use ONLY the NEGATIVE (-) Power (usually black or brown) & SIGNAL lines
(see table below) between the receiver throttle channel and the ESC's.
 
Do NOT use the POSITIVE (+) Power (usually Red) wires.  
The following table serves as a guide to common radio systems and their wiring schema and color usage. Use this table with caution. If in doubt, please defer to information provided by your radio supplier.  
 
RADIO BRAND NEGATIVE (-) SIGNAL
VRS & Futaba Black White
Airtronics Z Black Blue
JR Brown Orange
HiTec Black Yellow
f) Plug the ESC throttle control wires into the ends of the throttle Y-connector
 
g) Plug the remaining single end of the throttle Y connector into your receiver throttle channel.  
 
h) Use the airborne battery pack from your radio system to power your receiver. Do NOT attempt to use power from either BEC to power your receiver. You may wish to consider using a stand alone BEC such as that from Western Robotics to power your radio system but do NOT use the BEC's that are a part of many ESC's. They will not work in a twin power configuration.
 
i) Select suitable propellers for your motors and your speed controllers. The two props should be identical. Prop selection is vital with brushless motors. Overloading the motors and ESC by using the wrong prop can get very very expensive in a big hurry.
 
j) Verify that you can control the RPM of the motors via the receiver and that they produce similar RPM and thrust throughout the throttle range.  
 
Footnote: There are some dual ESC's that enable you to control two Brushless motors from one ESC. These eliminates the need for a second ESC and may make the installation of third party components simpler. If you are using a dual ESC, ensure that you follow the manufacturers instructions regarding wiring and operations.