ArticlesArticles Most Popular ArticlesMost Popular Articles Most Helpful ArticlesMost Helpful Articles Submit A QuestionSubmit A Question Login for PRIORITY RESPONSELogin for PRIORITY RESPONSE
RSS Feeds
DrillDown Icon Table of Contents Back
 . . . . . . . . . . . . .
DrillDown Icon LIABILITY & COPYRIGHT
DrillDown Icon Site Information
DrillDown Icon * Support
DrillDown Icon Technical Info - Adhesives
DrillDown Icon Technical Info - Master Airscrew
DrillDown Icon Technical Info - POLYPRO
DrillDown Icon Technical Info - RC Flying - General
DrillDown Icon Technical Info - RC Flying Electric - General
DrillDown Icon Technical Info - ULTRA POWER Technology - Products
DrillDown Icon Technical Info - VMAR - General
DrillDown Icon VMAR - Documents
DrillDown Icon VMAR - Adhesives
DrillDown Icon VMAR - Canopy (Window) Cleaning
DrillDown Icon VMAR - Canopy (Window) Replacement
DrillDown Icon VMAR - CG Location - General
DrillDown Icon VMAR - Cleaning Model Aircraft
DrillDown Icon VMAR - Construction
DrillDown Icon VMAR - Control Surfaces
DrillDown Icon VMAR - Covering
DrillDown Icon VMAR - Covering - What's on My Model?
DrillDown Icon VMAR - Covering - Color Changes
DrillDown Icon VMAR - Covering - Custom Graphics
DrillDown Icon VMAR - Covering - Not Factory Applied
DrillDown Icon VMAR - Covering - Patch Material
DrillDown Icon VMAR - Covering - Patches vs Sets
DrillDown Icon VMAR - Covering - POLYCOTE ECS
DrillDown Icon VMAR - Covering - VCOTE
DrillDown Icon VCOTE - What is it?
DrillDown Icon * VCOTE - Care & Maintenance
DrillDown Icon VCOTE - Introduction
DrillDown Icon VCOTE - Summary & Quick Tips
DrillDown Icon VCOTE - Avoid Hot Vehicles
DrillDown Icon VCOTE - Cleaning After Flying
DrillDown Icon VCOTE - Cleaning Initially
DrillDown Icon VCOTE - Cutting
DrillDown Icon VCOTE - Protecting the Finish
DrillDown Icon VCOTE - Removing & Using Tape
DrillDown Icon VCOTE - Repairing Punctures
DrillDown Icon VCOTE - Resealing Seams
DrillDown Icon VCOTE - Tightening Sags
DrillDown Icon VCOTE - Tools
DrillDown Icon VMAR - Covering - VCOTE2-3DS
DrillDown Icon VMAR - Covering - Tools - Recommended
DrillDown Icon VMAR - Cowl Installation
DrillDown Icon VMAR - Electric Power Conversions
DrillDown Icon VMAR - Engine Mounting
DrillDown Icon VMAR - Engine Power Module
DrillDown Icon VMAR - Flaps & Flaperons
DrillDown Icon VMAR - Fuel Leaks - Fuselage Soaked - What now?
DrillDown Icon VMAR - Fuel Proofing
DrillDown Icon VMAR - Fuel Tanks
DrillDown Icon VMAR - Glow Power Conversions
DrillDown Icon VMAR - Hardware & Fittings
DrillDown Icon VMAR - Jet (Turbine) Power Conversions
DrillDown Icon VMAR - Landing Gear
DrillDown Icon VMAR - Packaging
DrillDown Icon VMAR - Parts
DrillDown Icon VMAR - Servo Trays
DrillDown Icon VMAR - Specifications of Models
DrillDown Icon VMAR - Wings
DrillDown Icon VMAR - Wing Fairing Replacement
DrillDown Icon VMAR - Wood Types Used
DrillDown Icon Technical Info - VMAR - Products
DrillDown Icon Technical Info - VMAX Electric Power Systems - General
DrillDown Icon Technical Info - VMAX Electric Power Systems - Products
DrillDown Icon Technical Info - VMAX Engines (Glow) - General
DrillDown Icon Technical Info - VMAX Engines (Glow) - Products
  Email This ArticlePrint PreviewPrint Current Article/Category and All Sub-Articles/Categories
 
VCOTE - Care & Maintenance - Quick Tips

Question: Do you have any pointers regarding the Care & Maintenance of VCOTE?

Answer: Yes we have this Summary of Quick Tips and at www.richmondrc.com ( Enter Site > Support > Knowledge Base then Search on "Covering") we have an expanded explanation for each of these Tips.

VCOTE is a proprietary covering system engineered in Canada & available only from VMAR. Please note that VCOTE is NOT Monokote or Solarfilm, its different. As with any new modern technology, the maintenance methods may be different than those you used with your older covering so its important to read the Tips over FIRST. Whatever you want to do with VCOTE, test it on a small out of the way area first.

Here is our Summary of Quick Tips related to VCOTE covering.

  • Avoid Hot Vehicles
    • Cooking your model in your vehicle for hours on end is generally not a good idea! Temperatures can easily exceed 50C (122 F) under such conditions. You will get sags. Consult our Knowledge Base before attempting to remove sags.  
  • Cleaning After Flying
    • We recommend Fantastic household cleaner and disposable paper towels. Mist, do not flood. Wipe along seams, not across. Do NOT NOT NOT NOT use SIMPLE GREEN, 409 or similar materials for cleaning a model airplane.
  • Cleaning Initially
    • Upon initial inspection if you see a thin streaky film on any of the VCOTE, work outdoors and after testing first on a small out of the way area, use a paper towel and wipe a slightly wet film of Alcohol over 1/4 of a wing or half a fuselage at a time. Rub gently while still wet. Change towels frequently. Avoid plastics.
  • Cutting
    • Use sharp scissors or an XACTO knife with a sharp #11 blade.
  • Protecting the Finish
    • Most Importantly - Follow the cleaning instructions. Use the recommended cleaners and method. Avoid raw fuel with nitro content higher than 15%. Dab away all raw fuel regardless of nitro content. Test a small out of the way area and all plastics first before applying any glue, solvent, cleaner, paint or other preparation. Patch punctures promptly. Avoid hours and hours sitting the direct sun.
  • Removing & Using Tape
    • Use low tack tape. When removing, peal tape back on itself so that the pulling is parallel to the surface of the covering.
  • Repairing Punctures
    •  Patch promptly. Clean any oil residue from the area of the puncture. Patch should be 1/2" (13mm bigger) on all sides. Round the corners. Seal in place with a heat iron & sock. Tighten area with a heat gun.
  • Resealing Seams
    • Act promptly. Clean any oil residue from the area and reseal the seam with thin CA.
  • Tightening Sags
    • Remember SSB... SECURE the perimeter then SHRINK to fit then BOND to the structure. Use a heat gun and soft cotton cloth or glove and hand pressure to SECURE the perimeter, use a heat gun to SHRINK within the perimeter, use a soft cloth while the covering is warm to BOND the covering to solid substrates. Consult our Knowledge Base for further information.
  • Tools for Working with VCOTE
    • Scissors, XACTO with #11 blade, iron, iron sock, regulated heat gun, soft cotton cloth or glove.

 

Article ID: 4512